Ready-to-use microcement kit

Choose your surface and buy the complete kit.

Cementec’s ready-to-use microcement kits bring together the products for each stage (consolidation, base, fine coat and finish) for your type of surface. The microcement arrives mixed, weighed and pigmented at the factory, with no mixing on site, and you buy it direct from the manufacturer.

Made in Elda (Alicante, Spain)

Technical support for your project

Video tutorials included

Choose your microcement kit by surface

Each substrate needs different preparation. Tell us what you are going to cover and we will show you the products you need, with their prices and everything ready to request your quote

Kit for smooth surfaces

Plasterboard, plaster, MDF and furniture.

Consolidador · Fino · Primer · Finish Forte

“Ready to paint” surfaces: the quickest process.

Kit total

€138.89

Kit for cementitious surfaces

Self-levelling mortar, concrete and masonry floors.

Fibreglass mesh · Consolidador · Base · Fino · Primer · Finish Forte Plus

The standard kit for masonry floors and walls.

Kit total

€282.85

Kit for surfaces with joints

Ceramic, stoneware, tiles and marble (bathrooms and tiling).

Seal (epoxy sealer) · Fibreglass mesh · Base · Fino · Primer · Finish Forte Plus

Cover tiles without removing them.

Kit total

€322.92

Not sure which surface you have?

Smooth

Plasterboard, plaster, MDF or a piece of furniture. It is prepared as if for painting.

W

Cementitious

Self-levelling mortar or a concrete floor.

With joints

Ceramic, stoneware, tiles or marble; you can see the joints between the pieces.

If in doubt, ask us before you buy and we will advise you.

Microcement TV unit built on site, in a living room finished with ready-to-use microcement

Microcement kit for smooth surfaces (plasterboard, plaster or MDF) and furniture

Plasterboard, plaster and MDF are perfectly flat and are prepared as if for painting: fill, tape and sand. It is the easiest surface to start with ready-to-use microcement and the usual one for TV units, tables and wall coverings.

What the smooth surface kit includes

Cementec Consolidador, single-component epoxy primer for the microcement kit

Consolidador

€12.38

Cementec Fino ready-to-use microcement, finishing coat of the kit

Fino

€62.92

Cementec Primer, pore-sealing surface sealer for microcement

Primer

€20.84

Cementec Finish Forte, protective varnish for microcement

Finish Forte

€42.75

Tools you will need

1 flexible steel trowel

2 microfibre rollers

1 flat paintbrush

1 roll of masking tape

1 plastic tub

Kit total

RRP, VAT included

€138.89

  • Direct from the manufacturer
  • Technical support for your project
  • Delivery across mainland Spain
  • Shipping to the rest of Europe 48-72 hours

How to prepare a smooth surface

Fill, tape and sand

Use 80-grit sandpaper until the surface is flat.

Apply the Consolidador

Diluted with 30% water.

Leave to dry

Dries in 3-4 hours.

20 m²

Per litre of Consolidador

Bright showroom with a large window in Cementec ready-to-use microcement

Microcement kit for cementitious surfaces

On self-levelling mortar or a concrete floor, the key is to level and consolidate the substrate properly. It is the standard kit for masonry floors and walls.

What the cementitious surface kit includes

Cementec fibreglass mesh for microcement

Fibreglass mesh

€55.36

Cementec Consolidador, single-component epoxy primer for the microcement kit

Consolidador

€12.38

Cementec Base ready-to-use microcement, reinforcement coat of the kit

Base

€62.92

Cementec Fino ready-to-use microcement, finishing coat of the kit

Fino

€62.92

Cementec Primer, pore-sealing surface sealer for microcement

Primer

€20.84

Cementec Finish Forte Plus, high-protection varnish for microcement

Finish Forte Plus

€68.43

Tools you will need

1 flexible steel trowel

2 microfibre rollers

1 flat paintbrush

1 roll of masking tape

1 plastic tub

Kit total

RRP, VAT included

€282.85

  • Direct from the manufacturer
  • Technical support for your project
  • Delivery across mainland Spain
  • Shipping to the rest of Europe 48-72 hours

How to prepare a cementitious surface

Sand and repair cracks

Sand with 80 grit and wait at least 1 week after repairing large cracks.

Consolidate the substrate

Apply the Consolidador diluted to 30%.

Walkable in 24 hours

After the finish; protect it for 72 hours before working on it.

24 h

Until the floor is walkable

Bathroom renovated with Cementec microcement applied over tiles

Microcement kit for surfaces with joints

To cover tiles without removing them, you need to fill the joints and seal the substrate. That is why this kit includes Seal, an epoxy sealer, as well as the complete system. It is the standard kit for bathrooms and kitchens renovated over tiles.

What the kit for surfaces with joints includes

Cementec Seal, two-component epoxy primer for surfaces with joints

Seal

€52.45

Cementec fibreglass mesh for microcement

Fibreglass mesh

€55.36

Cementec Base ready-to-use microcement, reinforcement coat of the kit

Base

€62.92

Cementec Fino ready-to-use microcement, finishing coat of the kit

Fino

€62.92

Cementec Primer, pore-sealing surface sealer for microcement

Primer

€20.84

Cementec Finish Forte Plus, high-protection varnish for microcement

Finish Forte Plus

€68.43

Tools you will need

1 flexible steel trowel

2 microfibre rollers

1 flat paintbrush

1 roll of masking tape

1 plastic tub

Kit total

RRP, VAT included

€322.92

  • Direct from the manufacturer
  • Technical support for your project
  • Delivery across mainland Spain
  • Shipping to the rest of Europe 48-72 hours

How to prepare a surface with joints

Check and fill the joints

Repair loose or damaged pieces; use fine cement for joints under 5 mm and base for wider ones.

Sand once dry

After 4-6 hours of drying.

Apply the Seal sealer

At a 5:2 ratio and 150 g/m²; wait 12 to 24 hours.

150 g/m²

Of Seal sealer

Standard or Water Resistant microcement:
which should you choose?

Standard system

This is the system in the kits above: base with fibreglass mesh (on cementitious surfaces and surfaces with joints), fine coat in two coats of 0.5 kg/m², and a finish with Primer and Finish Forte.

Water Resistant system

It replaces the fine coat with Water Resistant microcement, in two coats of 0.6 kg/m², and is finished with the same Primer and topcoat. Designed for areas exposed to water, such as showers and bathrooms.

Microcement materials:
what a ready-to-use kit contains

Cementec Consolidador, single-component epoxy primer for the microcement kit

Consolidador

Cleans, consolidates and firms up the surface so that the following coats bond well.

See product sheet: Consolidador

Cementec Base ready-to-use microcement, reinforcement coat of the kit

Base and fibreglass mesh

Reinforcement coat with fibreglass mesh (145 g/m²): two coats of 1 kg/m² with a steel trowel.

See product sheets: Base · Fibreglass mesh

Cementec Fino ready-to-use microcement, finishing coat of the kit

Fino

The coat that gives the decorative finish: two coats of 0.5 kg/m² with a rounded-edge trowel, sanding between coats.

See product sheet: Fino

Cementec Primer, pore-sealing surface sealer for microcement

Primer and topcoat (Finish Forte / Finish Forte Plus)

Primer is diluted 20% with water and seals the surface; the topcoat (5:1 mix) protects it against moisture and wear.

See product sheets: Primer · Finish Forte · Finish Forte Plus

Cementec Seal, two-component epoxy primer for surfaces with joints

Seal (only on surfaces with joints)

Epoxy sealer that prepares the substrate before the system is applied.

See product sheet: Seal

How much microcement do I need?

Coverage per square metre with the Standard system:

Base

2 coats

of 1 kg/m²

Fino

2 coats

of 0.5 kg/m²

Consolidador

20 m²

per litre

Seal (joints only)

150 g/m²

on surfaces with joints

Measure the square metres you are going to cover and work out the quantities with our microcement price calculator, or write to us and we will help you.

Why buy your kit from Cementec

Direct from the manufacturer

Cementec makes ready-to-use microcement in Elda (Alicante, Spain): you buy from the manufacturer, with no intermediaries.

Ready to use, no mixing on site

It arrives mixed, weighed and pigmented at the factory: fewer steps, fewer mistakes and the same colour in every container.

Tested and controlled product

Every batch goes through quality control, and we keep a sample container for testing.

Technical support

Our technical department helps you with any question or issue during your project.

Fast delivery

24-48 h in Spain and 48-72 h in the rest of Europe from order confirmation.

How to apply a ready-to-use microcement kit

  1. Prepare the substrate: sanding, filling joints or repairing cracks.
  2. Consolidate with diluted Consolidador.
  3. Apply the base with fibreglass mesh, in two coats.
  4. Apply the fine coat (or Water Resistant), in two coats, sanding between them.
  5. Seal and protect with Primer and Finish Forte.

You will find the full step-by-step process in the application guide and in our application videos.

Are you a professional?
Get applicator pricing

If you work with a trowel, the Cementec Applicator Programme gives you online training, technical support and trade pricing.

Frequently asked questions about microcement kits

What does a Cementec microcement kit include?

The products for each stage according to the surface: Consolidador, base and fibreglass mesh (if the substrate requires it), fine coat, Primer and topcoat, plus Seal on surfaces with joints. Each product is shown with its price and a link to its product page.

Which kit do I need to cover tiles or a bathroom?

If you are covering tiles, the kit for surfaces with joints: it includes Seal, an epoxy sealer, so you can apply it over ceramic or stoneware without removing the pieces. If the bathroom is masonry (concrete or mortar), the cementitious surface kit. In areas exposed to water, ask about the Water Resistant system.

Which kit do I need for a piece of furniture?

The smooth surface kit, designed for plasterboard, plaster and MDF, which are the usual materials for TV units, tables and wall coverings.

Can I apply the kit if I am not a professional?

Yes, by following the preparation, application and finishing steps. As it is ready to use, there is no mixing on site, and our technical team will advise you if you need it.

What is the difference between Standard and Water Resistant?

The Water Resistant system replaces the fine coat with a coat of Water Resistant microcement (0.6 kg/m² per coat), designed for areas exposed to water. The rest of the system is the same.

How much microcement do I need per square metre?

With the Standard system, 2 kg/m² of base and 1 kg/m² of fine coat, plus Consolidador (20 m² per litre). Work out your quantities with the microcement price calculator.

When can I walk on a microcement floor?

After the second topcoat, the floor is walkable in 24 hours; we recommend waiting 72 hours, with protection (cardboard or geotextile), before working on it.

Can I buy the products separately?

Yes. Each product in the kit has its own product page, with its price, and you can order it separately.

How long will my order take to arrive?

Usually 24-48 h in Spain and 48-72 h in the rest of Europe from order confirmation.

Questions about your kit? We can advise you

Tell us what surface you are going to cover and how many square metres, and we will recommend the right kit before you buy.

We reply within 24 working hours.